TY - JOUR AU - Luijan, Jinkamon PY - 2018 TI - ประสิทธิภาพการปรับสภาพเกรนละเอียดและปรับสภาพเฟสยูเทคติกซิลิคอนในโลหะผสมหล่ออลูมิเนียม-ซิลิคอน-แมกนีเซียม JF - Naresuan University Journal: Science and Technology (NUJST); Vol 26 No 1 (2018): January - March 2018 KW - Engineering N2 -      การปรับสภาพเกรนละเอียดและปรับสภาพเฟสยูเทคติกซิลิคอนมีความสำคัญในการเพิ่มคุณภาพของชิ้นงานหล่อในโลหะผสมอลูมิเนียม-ซิลิคอน งานวิจัยนี้มีวัตถุประสงค์เพื่อศึกษาประสิทธิภาพการปรับสภาพเกรนละเอียดและการปรับสภาพเฟสยูเทคติกซิลิคอนในโลหะผสมอลูมิเนียม-ซิลิคอน-แมกนีเซียม เกรด A356 โลหะแม่ที่ใช้ในการทดลอง Al-4%B-2%Sr ปริมาณการเติมแตกต่างกัน (ร้อยละ 1, 2, 3 และ 4 โดยน้ำหนัก ตามลำดับ) เวลาในการค้างน้ำโลหะ (10, 30, 60 และ 120 นาที ตามลำดับ) เทลงโมลสแตนเลสผนังบางที่มีอัตราการเย็นตัวต่ำ ผลการทดลองพบว่าโลหะผสมอลูมิเนียมที่ไม่ได้ผ่านการปรับสภาพเกรนละเอียดและปรับสภาพเฟสซิลิคอนจะมีขนาดเกรนที่ใหญ่ และเฟสยูเทคติกซิลิคอนมีรูปร่างไม่แน่นอน หลังจากการเติมโลหะแม่ ร้อยละ 1 โดยน้ำหนัก ทำให้ขนาดเกรนลดลงเล็กน้อย ในขณะที่เฟสซิลิคอนจะปรับสภาพเป็นกลมมนแค่บางส่วน ปริมาณการเติม ร้อยละ 2, 3 โดยน้ำหนัก ขนาดเกรนเฉลี่ยเล็กลงอย่างมาก และเฟสยูเทคติกซิลิคอนเปลี่ยนเป็นรูปทรงกลมมนทั้งหมด นอกจากนี้ยังพบว่าที่ปริมาณการเติม ร้อยละ 4 โดยน้ำหนัก เวลาในการปรับสภาพ 10-120 นาที จะมีการฟอร์มตัวของสารประกอบ SrB 6 บริเวณด้านล่างของชิ้นงานหล่อ ซึ่งการฟอร์มตัวดังกล่าวส่งผลต่อประสิทธิภาพในการปรับสภาพเกรนละเอียดที่ลดลง      Refining efficiency and eutectic silicon modification are important to increase quality of Al-Si cast alloy. The objective of this research was to study the grain refining efficiency and eutectic silicon modification of Al-Si-Mg cast alloy grade A356 by adding master alloy, Al-4%B-2%Sr, in different portions (1, 2, 3 and 4 wt.% respectively) and within different holding times (10, 30, 60 and 120 min respectively) when pouring into stainless mold with low cooling rate. The experiment found that Al-Si-Mg cast alloy without passing the grain refining and eutectic silicon modification, had large grain size and acicular morphology of eutectic silicon. After the addition of 1 wt.% of Al-4%B-2%Sr, the grain size decreased while eutectic silicon’s morphology partially became fibrous. And after the addition of 2 and 3 wt.% of Al-4%B-2%Sr, the average grain sizes massively decreased and eutectic silicon fully modified into the fibrous morphology. However, the experiment found that the addition of 4 wt.% of Al-4%B-2%Sr, within hold times of 10-120 min caused SrB 6 intermetallic compound at the bottom of casting, leads to a decrease of refining efficiency. UR - https://www.journal.nu.ac.th/NUJST/article/view/1613